The Complete Guide

Kinetic Wireless Light Switches

Everything you need to know about the Forum Kinetic range: how it works, which parts to choose, how to fit it and how to pair it. No batteries, no wiring to the switch, and no channelling out walls.

How It Works

Press The Switch – The Light Comes On

Inside every Kinetic switch is a tiny generator. When you press the button, the movement creates just enough power to send a wireless radio signal (433 MHz). A small receiver, wired in at the light, picks up that signal and turns the light on or off. That's why the switch never needs a battery or a cable.

1. You Press

The press makes its own tiny burst of power

→

2. Wireless Signal

The switch sends a radio signal to its paired receiver

→

3. Light On / Off

The receiver at the light switches it on or off

PART 1

The Kinetic Switch

The bit you press. Battery-free and wire-free, so it can go almost anywhere – screwed to a back box or stuck to the wall, glass or furniture with the pad supplied.

PART 2

The Receiver

The bit that does the switching. It's wired into the lighting circuit (or plugs into a socket, or is built into a pendant or wall switch) and listens for your switch.

Every setup needs both parts: at least one Kinetic switch and one receiver. You can pair up to 10 switches to one receiver.
Where To Use It

Add A Switch Anywhere – Without Rewiring

Two-Way & Multi-Way

Add a second or third switch at the top of the stairs, the other end of a hallway or the back door – no new cables.

Bedside Switches

Turn the main light off from bed. Stick a switch to the headboard or bedside wall.

Kitchen Islands

Fit a switch on the island or worktop end where running a cable is difficult.

Lofts, Garages & Garden Rooms

Switch the loft light from the landing, or outbuilding lights from the house.

Bathrooms

The IP65 push switches are protected against dust and water jets, so they suit bathrooms and damp areas.

Extensions, Rentals & Older Homes

Ideal where you don't want to chase walls, disturb plaster or redecorate.

How To Choose

Choosing The Right Parts In 3 Steps

Step 1 – Choose Your Receiver

The receiver decides what your system can do: just on/off, phone and voice control, or dimming.

Receiver Type What It Does Best For Codes
Standard On/Off Simple wireless on and off from your Kinetic switches. No Wi-Fi needed. Most lighting circuits – adding a 2-way switch CUL-40038
CUL-45728
2 Channel On/Off Controls two separate lights or circuits from one receiver. Two lights in one room, e.g. main light + wall lights CUL-45730
Smart Wi-Fi On/Off On/off from your switches plus the Tuya Smart Life app, Alexa and Google Home. Timers and schedules. Smart homes, voice control, holiday timers CUL-40039
CUL-45729
Smart Wi-Fi Dimmer Wireless on/off and dimming, plus app and voice control. Living rooms, bedrooms, mood lighting CUL-40040
CUL-45731
6A On/Off Controller Heavier-duty on/off controller, standard or with Tuya Wi-Fi. Larger lighting loads CUL-47549
CUL-47550
Integrated Electric-To-Kinetic Switch Replaces your existing wall switch. Works as a normal switch and has a receiver built in, so you can add Kinetic switches elsewhere. No neutral needed. The quickest upgrade – swap the old switch, add wireless ones CUL-45722 (1G)
CUL-45723 (2G)
CUL-45724 (3G)
Plug-In Receiver Plugs into a 13A socket. Control lamps or appliances plugged into it – no wiring at all. Table and floor lamps, Christmas lights CUL-44766 (RF)
CUL-44767 (Smart)
B22 Pendant Kit A pendant set with the receiver built in. Replaces your existing pendant at the ceiling rose. Single pendant lights CUL-45732 (RF)
CUL-45733 (Smart)
Easiest start: our Pre-Paired Starter Kits come with a switch and receiver already paired – choose On/Off (CUL-47551), On/Off With Wi-Fi (CUL-47552) or On/Off With Wi-Fi & Dimming (CUL-47553).

Step 2 – Choose Your Switch Style

IP65

Push Switches

1, 2 or 3 gang in matt white or matt black. Standard UK plate size (86 × 86 mm). Bathroom-friendly.

DECORATIVE

Decorative & Slimline

Satin brass, satin nickel and black chrome fronts with black or white switches, plus slimline white and black. 1 or 2 gang.

GRID

Grid Modules

Kinetic modules that fit grid systems (slim grid, Click MiniGrid and BG compatible), with Forum surrounds, plated front plates and back housings. On/off or dimmable.

PORTABLE

Fob Switches

Handheld 1 or 2 gang fobs – a wireless remote for your lights that never needs a battery.

Gangs Explained

Each gang (button) controls one receiver. A 1 gang switch controls one light; a 2 gang controls two separate lights; a 3 gang controls three. For dimming, the dimmable 2-way centre retractive grid modules and 2 gang switches give you on/off on one side and dim on the other.

Step 3 – How Many Do You Need?

  • One receiver per light (or circuit) you want to control.
  • As many switches as you like on each receiver – up to 10.
  • Want a light switched from three places? That's 1 receiver + 3 switches.
  • Want two different lights switched from one place? Use a 2 gang switch + 2 receivers (or a 2 channel receiver).
How To Install

Fitting Your Kinetic System

RECEIVER

Fitting The Receiver

  1. Isolate the power at the consumer unit before you start.
  2. Wire it in: Live and Neutral to the input terminals, and the light to the output terminals. The receiver usually sits at the ceiling rose, behind the light fitting or in a back box.
  3. Fix it in place with the screws or sticky pad supplied.
  4. Leave at least 50 mm space around it and never cover it with insulation.
Wired receivers must be fitted by a qualified electrician. Standard receivers are for indoor, dry locations (IP20). Plug-in receivers need no wiring.
SWITCH

Fitting The Switch

  1. Pair it first (see below) and test it where you plan to fit it.
  2. To open the cover, put a coin in the gap and twist gently.
  3. Screw fixing: fix the base to a standard back box, then clip the cover back on.
  4. Stick-on fixing: clean the surface, peel the backing off the pad and press firmly in place.
No wiring, no electrician needed for the switch – anyone can fit it.
How To Pair

Pairing Your Switch To The Receiver

Standard Pairing

  1. With the receiver powered, hold its pairing button for 3–4 seconds until the red light flashes slowly.
  2. While it's flashing, press your Kinetic switch once.
  3. The light will flash to confirm. Done – repeat for any other switches (up to 10).

Adding A Switch Without Reaching The Receiver

If the receiver is already fitted out of reach (e.g. in the ceiling):

  1. Press an already-paired switch 8 times within 6 seconds.
  2. The receiver opens a pairing window.
  3. Press the new switch once to pair it.

Connecting To The App (Smart Receivers)

  1. Download the Tuya Smart Life app.
  2. Connect your phone to your 2.4 GHz Wi-Fi (5 GHz networks are not compatible).
  3. Add the device in the app – the blue light flashes while pairing and stops when connected.
  4. Link Smart Life to Alexa or Google Home for voice control.

Un-Pairing & Resetting

  • Clear paired switches: hold the receiver's pairing button for about 6–7 seconds.
  • Reset the Wi-Fi / app connection: hold it for about 10–15 seconds.
Pair one switch to one receiver. Pairing the same switch to several receivers can make them fall out of sync – use a 2 or 3 gang switch instead.
Dimming & Smart Control

Dimming, App & Voice Control

Dimming

  • You need a dimmer receiver (CUL-40040 or CUL-45731) and a dimmable switch.
  • One button turns the light on and off; the other adjusts the brightness, with a soft start from off.
  • Use dimmable LED lamps, and set the minimum and maximum brightness in the app for the smoothest dimming.

Smart Receivers Work With Alexa & Google Home

  • Control your lights from your phone, anywhere.
  • Voice control through Alexa and Google Home.
  • Timers and schedules – great for security when you're away.
  • Your Kinetic switches still work as normal, even without Wi-Fi.
Range & Specs

At A Glance

0Batteries & no wiring to the switch
Up To 10Switches on one receiver
IP65Push switches – bathroom-friendly
100,000+Presses lifespan
433 MHzRadio frequency
Typical Range Distance
Open space (outdoors, nothing in the way) Up to 40 m
Indoors through plasterboard / stud walls Up to 15 m
Indoors through brick, concrete or glass Up to 8 m

Range varies with the building. Many newer models reach further; these are safe, everyday figures.

Range tips: metal (foil-backed plasterboard, steel beams, metal back boxes and enclosures) and thick walls shorten the range. Always test the switch in position before fixing it, and fit the receiver as close to the switch as practical.
FAQs

Frequently Asked Questions

Will I Ever Need To Change A Battery?

No. The switch makes its own power every time you press it. There is no battery inside to change.

Do I Need An Electrician?

For the switch, no – it has no wires. Wired receivers, integrated switches and pendant kits connect to mains electricity and must be fitted by a qualified electrician. Plug-in receivers just plug into a socket.

How Many Switches Can I Use On One Light?

Up to 10 Kinetic switches can be paired to one receiver.

Can One Button Control Two Lights?

We don't recommend pairing one switch to several receivers, as they can fall out of sync. Use a 2 or 3 gang switch, or a 2 channel receiver, instead.

Can I Use Them In A Bathroom?

Yes – the IP65 push switches are protected against dust and water jets. Receivers are IP20 and must be fitted in a dry location, away from water.

Do The Smart Receivers Need Wi-Fi To Work?

Only for app and voice control. Your Kinetic switches still work without Wi-Fi. Smart receivers need a 2.4 GHz Wi-Fi network – 5 GHz only networks are not compatible.

What Happens In A Power Cut?

The receiver needs mains power to switch your light, just like any light fitting. When the power comes back, your switches carry on working as normal.

Will It Work With My Existing Light Switch?

Yes. Fit a receiver in the circuit, or use an Integrated Electric-To-Kinetic Switch to replace your existing switch – it works as a normal switch and lets you add wireless Kinetic switches elsewhere.

Can I Dim My Lights?

Yes, with a dimmer receiver (CUL-40040 or CUL-45731), a dimmable switch and dimmable LED lamps.

Not Sure What You Need?

Pop into the shop at 366 Uxbridge Road, Hatch End, or call us on 020 8428 0581 – we'll help you pick the right switches and receivers. Kinetic products are ordered in: Lead Time 2–3 Working Days.